Mapei Kerapoxy Design 2 Part Epoxy Grout 3kg (Choice Of Colour)

Your one stop tile tool shop

Two-component, decorative, satin finish, acid-resistant epoxy

For grout joints 3-10mm.

Available in 25 colours.

Can also be mixed with MAPEGLITTER

Product Name
Price (ex)
Price (inc)
Options
Info
£31.05
£37.26
£29.99
£35.99
£31.05
£37.26
£31.05
£37.26
£31.05
£37.26
£31.05
£37.26
£31.05
£37.26
£31.05
£37.26
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£31.05
£37.26
£29.99
£35.99
£31.05
£37.26
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
£31.05
£37.26
£29.99
£35.99
£29.99
£35.99
£31.05
£37.26
£29.99
£35.99
£29.99
£35.99
£29.99
£35.99
Work out how much you need

Using the calculator below, you can work out how much material you will need to get the job done. Please either enter your required area m2 or the width and length.

or
x
Estimated Total:

This is a rough guide calculation provided in good faith, actual usage may vary, please allow for wastage when placing your order. Pro Tiler Ltd can't be held responsible for any under ordering.

Description
Features
Attachments

Suitable for:

Installing and grouting decorative finishes in environments with an high aesthetic value (e.g. showrooms, commercial environments, etc.).

Suitable for application on substrates where a semi-transparent finish is required, it also allows the light to filter through (e.g. glass substrates).

Installing and grouting floors and walls in showers and bathrooms. Suitable on fibreglass and PVC substrates.

Installing and grouting floors and walls in thermal facilities, saunas, Turkish baths, etc.).

Installing and grouting in swimming pools, especially recommended for pools containing spa or sea water.

Repairing existing degraded grout by removing all loose areas and to a minimum uniform depth of 3 mm.

uniform colours resistant to ultra-violet light and atmospheric agents;

Excellent bonding properties. 

Application:

Spread Kerapoxy Design with a special MAPEI grout float, making sure that the joints are filled right down to the bottom. Remove excess material by passing the edge of the same trowel diagonally over the tile joints.

Finish:

Tiled finishes must be cleaned after grouting while Kerapoxy Design is still “fresh”. Wet the grouted surface and emulsify with an abrasive pad for cleaning joints (such as Scotch-Brite® or MAPEI tile-joint cleaning kit). Take care not to drag grout from the joint. Tiles/mosaics may also be cleaned with the same pad, but it must be more saturated with water. Any liquid which remains on the surface may be removed with a hard, cellulose sponge (such as a MAPEI sponge). Replace the sponge when it is coated with too much resin, and also when finishing off the grouted joints. After the finishing operation, it is very important that no traces of Kerapoxy Design remain on the surface of the tiles. Once hardened, it is very difficult to remove. Therefore, rinse the sponge often with clean water during cleaning. With very large floor surfaces, finishing may be carried out by wetting the surface and using a single-head rotary machine with special abrasive felt disks such as Scotch-Brite®. Residual liquid may be drawn off using a rubber rake. Kerapoxy Cleaner (special cleaning solution for epoxy grout) may also be used for the final cleaning cycle and may also be used to remove thin residues of grout up to several hours after application. In this case, the product must be left to react for longer (at least 15-20 minutes). The efficiency of Kerapoxy Cleaner depends on the amount of residual resin and the amount of time gone by after application. Cleaning must be carried out while still “fresh” as described above